-
DL-0174 Surgical Blade Elasticity Tester
The tester is designed and manufactured according to YY0174-2005 “Scalpel blade”. Main principle is as follows: apply a certain force to the centre of the blade until a special column thrusts the blade to a specified angle; maintain it in this position for 10s. Remove the applied force and measure the amount of deformation.
It consists of PLC, touch screen, step motor, transmission unit, centimeter dial gauge, printer, etc. Both product specification and column travel are settable. Column travel, time of testing and the amount of deformation can be displayed on the touch screen, and all of them can be printed by the built-in printer.
Column travel: 0~50mm; resolution: 0.01mm
Error of deformation amount: within ±0.04mm -
FG-A Suture Diameter Gauge tester
Technical Parameters:
Minimum graduation: 0.001mm
Diameter of presser foot: 10mm~15mm
Presser foot load on the suture: 90g~210g
The gauge is used for determining the diameter of sutures. -
FQ-A Suture Needle Cutting Force Tester
The tester consists of PLC, touch screen, load sensor, force measuring unit, transmission unit, printer, etc. Operators can set parameters on the touch screen. The apparatus can run the test automatically and display the maximum and mean value of cutting force in real time. And it can automatically judge whether the needle is eligible or not. The built-in printer can print the test report.
Load capacity (of cutting force): 0~30N; error≤0.3N; resolution: 0.01N
Test speed ≤0.098N/s -
MF-A Blister Pack Leak Tester
The tester is applied in the pharmaceutical and food industries for checking air-tightness of packages (i.e. blisters, injection vials, etc. ) under negative pressure.
Negative pressure test: -100kPa~-50kPa; resolution: -0.1kPa;
Error: within ±2.5% of reading
Duration: 5s~99.9s; error: within ±1s -
NM-0613 Leak Tester for Empty Plastics Container
The tester is designed according to GB 14232.1-2004 (idt ISO 3826-1:2003 Plastics collapsible containers for human blood and blood components – Part 1: Conventional containers) and YY0613-2007 “Blood components separation sets for single use, centrifuge bag type”. It applies an internal air pressure to the plastics container (i.e blood bags, infusion bags, tubes, etc.) for air leakage test. In use of absolute pressure transmitter matched with secondary meter, it has advantages of constant pressure, high precision, clear display and easy handling.
Positive pressure output: settable from 15kPa to 50kPa above local atmospheric pressure; with LED digital display: error: within ±2% of reading. -
RQ868-A Medical Material Heat Seal Strength Tester
The tester is designed and manufactured according to EN868-5 “Packaging materials and systems for medical devices which are to be sterilized—Part 5: Heat and self-sealable pouches and reels of paper and plastic film construction—Requirements and test methods”. It is used for determining the strength of the heat seal joint for pouches and reel material.
Itconsists of PLC, touch screen, transmission unit, step motor, sensor, jaw, printer, etc. Operators can choose the needed option, set each parameter, and start the test on the touch screen. The tester can record the maximum and average heat seal strength and from the curve of the heat seal strentgth of each test piece in N per 15mm width. The built-in printer can print the test report.
Peeling force: 0~50N; resolution: 0.01N; error: within ±2% of reading
Separation rate: 200mm/min, 250 mm/min and 300mm/min; error: within ±5% of reading -
WM-0613 Plastic Container Burst and Seal Strength Tester
The tester is designed according to GB 14232.1-2004 (idt ISO 3826-1:2003 Plastics collapsible containers for human blood and blood components – Part 1: Conventional containers) and YY0613-2007 “Blood components separation sets for single use, centrifuge bag type”. It uses transmission unit to squeeze the plastics container (i.e. blood bags, infusion bags, etc. ) between two plates for lquid leakage test and digitally displays the value of pressure, so it has advantages of constant pressure, high precision, clear display and easy handling.
Range of negative pressure: settable from 15kPa to 50kPa above local atmospheric pressure; with LED digital display; error: within±2% of reading. -
Pump Line Performance Detector
Style: FD-1
The tester is designed and manufacturer according to YY0267-2016 5.5.10 <<Hemodialysis and Hemopurification Device External Circle Blood Line>> It applies external blood line examination1)、Flow range at 50ml/min ~ 600ml/min
2)、Accuracy: 0.2%
3)、Negative pressure range: -33.3kPa-0kPa;
4)、High precise mass flowmeter installed;
5)、Thermostatic water bath installed;
6)、Keep constant negative pressure
7)、Testing result automatically printed
8)、Real-time display for error range -
Waste Liquid Bag Leakage Detector
Style: CYDJLY
1）Differential Pressure Transducer: accuracy±0.07%FS RSS,, Measurement accuracy±1Pa, but ±2Pa when below 50Pa;
Min. Display:0.1Pa;
Display range: ±500 Pa;
Transducer range: ±500 Pa;
Max. pressure resistance on one side of the transducer: 0.7MPa.
2）Leakage rate display range: 0.0Pa~±500.0Pa
3）Leakage rate limitation: 0.0Pa~ ±500.0Pa
4）Pressure transducer: transducer range: 0-100kPa,Accuracy ±0.3%FS
5）Channels: 20(0-19)
6）Time: Set range:0.0s to 999.9s. -
Extrusion Machine for Medical Products
Technical parameters: (1)Tube cutting diameter(mm): Ф1.7-Ф16 (2)Tube cutting length(mm): 10-2000 (3)Tube cutting speed: 30-80m/min(tube surface temperature under 20℃) (4)Tube cutting repeat precision: ≦±1-5mm (5)Tube cutting thickness: 0.3mm-2.5mm (6)Air flow: 0.4-0.8Kpa (7)Motor: 3KW (8)Size(mm): 3300*600*1450 (9)Weight(kg): 650 Automatic cutter parts list (standard) NAME MODEL BRAND FREQUENCY INVERTER DT SERIES MITSUBISHI PLC PROGRAMMABLE S7 SEIRES SIEMENS SERVO ...
